Software House

Just like processors, overclock a graphics card, according to the term, is to make the clock
on the graphics card to work beyond the specifications set by the manufacturer.
Generally, overclock graphics card is done by raising the core clock (its VGA chip) or by increasing clock of the memory used.

The best combination is to raise the clock of the second these components, both core chip and memory used.

On graphics cards that have major limitations in memory bandwidth, increasing clock
memory will provide more significant improvement compared with the increase of the core clock only.

GeForce 2 MX and its variants are graphics cards that are in the bottleneck that has on
memory.
In general, the memory overclock GeForce 2 MX will provide more significant results
compared to overclock the chip nVidia own. Graphics card is another type, each
have properties that vary, depending on the architecture used.
How to overclock this graphics card, the most common way is through a software /
program is designed for it, such as RivaTuner, Rage 3d Tweak, and GeForce Tweak Utility.

Often the drivers that came with your graphics card has a facility to overclock.
With take advantage of this innate facility or program specifically designed to overclock the card graphics, you can increase the value of the core clock and memory to achieve the maximum value of still be well received by your graphics card. Of course, improvement procedures performed slowly.

One thing you notice is necessary stability and appearance of your graphics card.
If stability has been disrupted and the resulting picture has begun to have artifacts
not desirable, should the core clock and memory derived from. Coercion clock value
overload can damage the graphics card permanently. Overclock itself usually will result in
the temperature of the graphics card becomes hotter than the condition when not in-overclock.

This can lower the age of the graphics card itself. To add stability and dissipates heat which
excessive, can use additional fans or heatsinks on the graphics card in question.
Replacement of the fan and the old heatsink with a more powerful and can also be large.
Use of these heatsinks and fans can also be applied to the memory chip, the chip is not limited to VGA only. Air circulation in the casing should also be noted, the smooth flow of air will help heat transfer occurs.

In addition to the program specifically designed for overclocking, overclocking can also be done through the BIOS. Overclock through the BIOS is usually done by replacing the BIOS of the graphics card used by the BIOS from a third party which is designed with a higher clock. Overclock way This is not too often performed, since the BIOS from a third party who has the criteria as desired is rare enough.

Overclock also be done through the BIOS on the mainboard (not all types of mainboard),
especially with a choice of multiplier for the AGP bus to the Front Side Bus (FSB) which can be selected manually, generally 1:2 and 2:3.

To mainboard that do not have a choice like this, overclock AGP bus will overclock overall system. With a choice of 1:2 and 2:3, you can overclock Your AGP bus, it's just extreme. As an illustration for a system with a FSB registration 133 MHz, the multiplier that is used by default is 1:2 so the bus is 66MHz AGP.

When the multiplier manually changed to 2:3 then the AGP bus will have a clock of 88.67 MHz. Depending graphics card is used, this configuration may be well received, although it can also stability be disturbed or even the system will not lit at all. One thing to remember
is, a configuration like this can damage your graphics card permanently. The risk of overclocking techniques This is great, so you should not try it unless you really know that
Your graphics card can accept AGP clock configuration like this.

DOWNLOAD
- RivaTuner
- Ati Tool

Before starting, prepare manuals and the first objects that describe the motherboard configurations, processor, and RAM, because a lot of information that we seek will be there. What if the book manual is lost or not supplied by the seller when you buy? Do not worry, the trick specific and a little luck, maybe we can get information about our hardware.
Luck is very dependent on the brand motherboard you buy.

- To begin, make sure your system is in state standards and you have made optimize windows.
- To ensure that the system in a state you can use your standard sisoft sandra, aida 32, or Everest to check all the settings related to the operating frequency PC system.
If you need to run 3D Mark 2001 was once just to test the initial stability and then record
score.
- Also make sure you have understood well the characteristics of hardware that will at overclock.
- Restart your PC, go into the BIOS search for the feature FSB and multiplier settings.
- Ensure Frequency AGP / PCI = 66 MHz / 33 MHz to enable the AGP divider (if any) or PCI frequency lock to AGP / PCI is not affected by the rising share FSB, this setting for performance of vga.
Usually the motherboard is the latest include features ini. Why PCI lock? because if the AGP / PCI guaranteed ride the system will run unstable.
As we all know the hard drive is one of the components connected to the IDE port, and IDE
- includes components that are controlled by the PCI south bridge chipset, which helped increase the frequency if there increase FSB.
What result if the frequency increases the IDE work? which obviously would happen interference on the hard drive platter so that the data be korup.Dengan for this reason that we must maintain order AGP / PCI fixed at standard conditions.
- The next step was raising FSB at 1MHz increment, then save the changes in the BIOS. The first step This is usually successful.

If the windows run smoothly restart your PC and go into the BIOS and then repeat
above steps again until you get a situation where the PC can still boot but was not able to
entry windows.

- Until here there are several possibilities why not get into windows.
Likelihood The first voltage and power shortages of power supply, for now the best choice is power supply 500 Watt.

- The second possibility is your processor is not able anymore to overclock.

• Likelihood The third quality of the motherboard that is not for overclocking purposes.

What if a third possibility of the above has been fulfilled? means are all eligible. Means you must decrease multiplier.

- Try down 0.5 point and then restart again.
If it still hangs, repeat the steps above to get in here windows. until success. How easy is that? Yes indeed! But do not be happy first ... you have to do that for the procession popular among overclockers called Benchmark.

If your computer is going to burn some time and then hangs, most likely caused by the hot processor excess.

If this happens, try opening your computer case, and wait a few minutes. Then turn on the computer again.

If a few moments later, with the same intervals as before, the computer hangs again experience, meaning processor was defeated.

In addition, there is sometimes also caused hangs on the CPU clock signal is blurred. That is, restrictions between logic 0 and 1 on a clock signal is not clear (in the computer, the signals are represented as binary with 0 and 1).
To overcome this, try to raise the working voltage processors ..

Overclock type The relationship between CPU clock and bus clock is woven by a multiplier.
In simple, CPU clock = bus clock x multiplier. For example, AMD Athlon XP 2000 + with a clock speed default is 1666 MHz the resultss of 133 MHz bus clock with multiplier 12.5 (twelve half).

Pentium 4 2.4 GHz is the results of 200 MHz bus with the multiplier 12.
Could also 266 bus clock multiplication with multiplier 9. Why, it becomes 2.394 GHz?
deed, there is rounding to be a whole number. Thus, for to overclock, which can enhanced is the bus clock, multiplier, or both. If the multiplier raised, then the CPU clock will go up, but the bus clock fixed.

Overclock requirements example :
For the example above, the AMD Athlon XP 2 GHz + (1666 Mhz real), if multiplier raised became 20, then the CPU clock rises 2660 MHz to be real. But if bus clock is raised, automatically CPU clock will also rise.

For example, Pentium 4 2.4 GHz with 200 MHz bus clock and multiplier 12 will be Pentium 4 3 GHz if the bus clock was encouraged to 266 MHz. It would be better if the is raised clocknya bus.

try this for step to overclock.
But The second alternative is more difficult considering peripheral capabilities connected to the bus may not be able to work above the standard clock. If CPU
clock is fixed, while the bus was still strong, down just multiplier and increase bus clock ..
This is still better than the alternative first.